X410 Tilley 659XA

Discussion in 'X410-X410A-X458-X460' started by dwillie, Sep 27, 2016.

  1. dwillie United States

    Offline
    Joined:
    Feb 17, 2013
    Messages:
    132
    Location:
    Wisconsin, USA
    New seals, and seems to run well. 1474940816-410_001.JPG 1474940853-410_003.JPG 1474940889-410_002.JPG 1474940920-410_004.JPG
     
    Last edited by a moderator: Apr 1, 2017
  2. Mackburner

    Mackburner United Kingdom Founder Member Subscriber

    Offline
    Joined:
    Sep 10, 2010
    Messages:
    6,045
    Location:
    Hertfordshire
    Cute little lamps these. This is the older one with the twin air tube burner. The later X410A has a three air tube burner. Nice to see another running. Rare things in the UK. I think nearly all of them were exported to the US. ::Neil::
     
  3. David Shouksmith

    David Shouksmith United Kingdom Founder Member

    Offline
    Joined:
    Sep 6, 2010
    Messages:
    6,668
    Location:
    North-East England
    I like them too and some seem to have found their way (back) to Great Lumley - which is nice... :D :thumbup:
     
    Last edited by a moderator: Mar 31, 2017
  4. Henry Plews

    Henry Plews Subscriber

    Offline
    Joined:
    Jun 23, 2014
    Messages:
    899
    Location:
    North Yorkshire
    And some have even found their way to Skipton.

    Henry.
     
  5. dwillie United States

    Offline
    Joined:
    Feb 17, 2013
    Messages:
    132
    Location:
    Wisconsin, USA
    Thank you for the replies. Is there a chart with the lengths of Tilley vaporizers? I dont understand this 410 has an odd length, and I dont see any reference to an actual number.
     
  6. David Shouksmith

    David Shouksmith United Kingdom Founder Member

    Offline
    Joined:
    Sep 6, 2010
    Messages:
    6,668
    Location:
    North-East England
    Not that I'm aware of but there weren't that many different vapourisers, anyway. As well as the 169 and 606, there was the 301, I think, in 500cp donuts, the iron vapouriser, the CS56 / CS22 stove one, the X410 one and the leak detector one. The last five would have been used in small or very small numbers. Any more?
     
    Last edited by a moderator: Mar 31, 2017
  7. Mackburner

    Mackburner United Kingdom Founder Member Subscriber

    Offline
    Joined:
    Sep 10, 2010
    Messages:
    6,045
    Location:
    Hertfordshire
    As far as I know this is the list. I don't know the lengths of all though.

    169 All pre WW2 lamps and lanterns 7”
    301 All 500 cp lamps 7"
    606 IL lamps and all post WW2 lanterns 5”
    951 Leak detectors
    1560 C S stoves 3.5”
    1865 X410 200cp type lanterns

    ::Neil::
     
  8. dwillie United States

    Offline
    Joined:
    Feb 17, 2013
    Messages:
    132
    Location:
    Wisconsin, USA
    Thanks Neil! Written down and filed.
     
  9. JEFF JOHNSON

    JEFF JOHNSON United Kingdom Subscriber

    Offline
    Joined:
    Nov 28, 2010
    Messages:
    9,017
    Location:
    Shetland Islands UK..
    The 606 vapouriser was also used on some of the AL., lamps.
     
  10. David Shouksmith

    David Shouksmith United Kingdom Founder Member

    Offline
    Joined:
    Sep 6, 2010
    Messages:
    6,668
    Location:
    North-East England
    I think the LD1 and LD2 leak detectors have different vapourisers. The LD1 is the typical Tilley vapouriser style although I don't have one handy to measure the length. The LD2 is more like the iron vapouriser with an adjustment knob. Now I do have two of those close to hand but I'm not taking them apart just to measure the vapouriser length... :doh:

    Edit: OK, I've just had a scrat around in my vapouriser box. As Neil says, the 606 and 169 are 5" and 7" in length overall but not including the bit of the pricker wire that sticks out of the bottom end.

    The 301 is also 7" long.

    The LD1 leak detector uses the 951 vapouriser which is slightly under 3 1/2" (95mm) long. The cleaning wire is Part No.961

    The CS22 and CS56 stoves both use the 1560 vapouriser which is exactly the same length as the 951. The cleaning wire is Part No. 1561.

    For the DN250 and DN250A irons, I have two vapourisers - the 2568A which is complete with the cleaning wire and control knob (and fuel feed pipe). Alternatively, there's the plain vapouriser without the control knob and fuel pipe. That one is 4 5/16" (109.5mm) long.
     
  11. dwillie United States

    Offline
    Joined:
    Feb 17, 2013
    Messages:
    132
    Location:
    Wisconsin, USA
    The 1865 is i believe 6" long from bottom of thread to jet tip then. Thanks for this info. i have learned a lot. A 169 on this 410 looks odd. I didnt try the 606. I would think it would be hard to preheat.
     
  12. Henry Plews

    Henry Plews Subscriber

    Offline
    Joined:
    Jun 23, 2014
    Messages:
    899
    Location:
    North Yorkshire
    Mmm, I've just been measuring too. The 606 is in fact 5 25/32 inches (134 mm) overall.
    The 3 examples of 1865 all measure 5 11/16 inches (144 mm).

    Henry.
     
  13. Mackburner

    Mackburner United Kingdom Founder Member Subscriber

    Offline
    Joined:
    Sep 10, 2010
    Messages:
    6,045
    Location:
    Hertfordshire
    X410 and the other lamps with that burner are all rated at 200cp which is why they have a different vaporiser to the normal 300cp lamps. I have never tried a 606 or 169 in one of these but I suspect they would probably work well enough. 606 is near enough in length to look about right. I would be interested to know how it performs. ::Neil::
     
  14. Anthony

    Anthony Australia Subscriber

    Offline
    Joined:
    May 7, 2013
    Messages:
    807
    Location:
    Melbourne, Australia
    I have a just under 3 3/4 inch and a 3 inch vapouriser.
    Any ideas ?
     
  15. David Shouksmith

    David Shouksmith United Kingdom Founder Member

    Offline
    Joined:
    Sep 6, 2010
    Messages:
    6,668
    Location:
    North-East England
    Well Henry - I've just been re-measuring :) and I see the 606 is 5" from the tip to the bottom of the knurled finger-nut and not to the bottom of the thread as I said earlier... :oops: :doh:

    From the tip to the bottom of the thread is 134mm as you say but that comes to 5 1/4" on my rule and maybe 5 5/16" (135mm) including the little nipple at the jet end...
     
    Last edited by a moderator: Mar 31, 2017
  16. Anthony

    Anthony Australia Subscriber

    Offline
    Joined:
    May 7, 2013
    Messages:
    807
    Location:
    Melbourne, Australia
    That would make my 3 3/4 a 3 1/2 inch so that sorts that one out but the 3 inch is now a 2.7 inch.
     
  17. David Shouksmith

    David Shouksmith United Kingdom Founder Member

    Offline
    Joined:
    Sep 6, 2010
    Messages:
    6,668
    Location:
    North-East England
    :-k Yes and no - it could be a 951 for the Mark I leak detectors or a 1560 for the CS22/CS56 camping stoves, both of which are 3 1/2"...
     
  18. Henry Plews

    Henry Plews Subscriber

    Offline
    Joined:
    Jun 23, 2014
    Messages:
    899
    Location:
    North Yorkshire
    David,

    My apologies, I should have taken more care when reading your post. Also, I seem to have mislaid my calipers so I used a tape measure which is the probable cause of my inaccuracies.

    Henry.
     
  19. David Shouksmith

    David Shouksmith United Kingdom Founder Member

    Offline
    Joined:
    Sep 6, 2010
    Messages:
    6,668
    Location:
    North-East England
    No need for an apology at all, Henry - as ever, I was primarily concerned with getting accurate information put on record here and correcting my own silly mistake... :doh: :oops:
     

Share This Page