AFC 1022 globe /mantle

Discussion in 'Pressure Lamp Discussion Forum' started by Scotlamp, Jul 10, 2016.

  1. Scotlamp

    Scotlamp United Kingdom Subscriber

    Offline
    Joined:
    Sep 15, 2015
    Messages:
    228
    Location:
    Kent UK
    Good Morning all would someone be kind enough to suggest what mantles to use and what globe to use .
    If feasible to fettle ? Boot fair find this morning

    1468142713-20160710_100608_opt.jpg .
     

    Attached Files:

  2. David Shouksmith

    David Shouksmith United Kingdom Founder Member

    Offline
    Joined:
    Sep 6, 2010
    Messages:
    8,413
    Location:
    North-East England
    AFC (Ash Flash Corporation) is a far-eastern copy of one of the Coleman lanterns so one of those globes will fit and also one of the Coleman mantles will be suitable - probably the 21 at a guess. Someone here will know which globe and mantle it is. Fettling should be straightforward.

    Happy pumping with the little fella! ;) :lol:
     
  3. Scotlamp

    Scotlamp United Kingdom Subscriber

    Offline
    Joined:
    Sep 15, 2015
    Messages:
    228
    Location:
    Kent UK
    Thank you for that David
    If you see. In the picture the band that sits on the tank , is not seated properly it's slightly to the right , Having worked on it this is still the case , looks like l will need to adjust the valve assembly , anti- clockwise a bit unless someone. knows any different , l dunked it and no leaks , knowing l can get the parts l will persevere tanks again.
    Michael,
    Upon a hill there stood a dookit it nae there noo cause someone took it.
     
  4. Scotlamp

    Scotlamp United Kingdom Subscriber

    Offline
    Joined:
    Sep 15, 2015
    Messages:
    228
    Location:
    Kent UK
    Thanks again !
     
  5. Scotlamp

    Scotlamp United Kingdom Subscriber

    Offline
    Joined:
    Sep 15, 2015
    Messages:
    228
    Location:
    Kent UK
    Got it going :D/ Thought I needed a seal for the thread to tank, used thinnest seal I could find .
    Gave myself more trouble as this had the effect of reducing the flow of fuel ,as I effectively raised the cleaning needle to high , thereby restricting flow of fuel .
    In conjunction with this---
    Had some trouble with the main valve assembly (off centre ) Thought it had been forced to much round and when mounting the frame etc
    long story short whipped some PTFE tape round thread .
    Solved centered and no more restriction .

    1468964445-20160719_214439_opt.jpg

    Michael

    The wind the wind the blustery wind that blew the skirts so high,
    But, god was just and made the dust, that blinned the wicked eye.
     

    Attached Files:

  6. Scotlamp

    Scotlamp United Kingdom Subscriber

    Offline
    Joined:
    Sep 15, 2015
    Messages:
    228
    Location:
    Kent UK
    Globe arriving tomorrow.moving it on, temptation to fit mantles is horrendous . such a waste . May be yes may be no ????

    Michael
     
  7. Scotlamp

    Scotlamp United Kingdom Subscriber

    Offline
    Joined:
    Sep 15, 2015
    Messages:
    228
    Location:
    Kent UK
    Running in, May be the wrong globe, But I like it .

    1469291417-20160722_154841_opt.jpg
     

    Attached Files:

  8. ROBBO55

    ROBBO55 Subscriber

    Offline
    Joined:
    Oct 21, 2014
    Messages:
    4,204
    Location:
    Somersby, New South Wales, Australia
    Cleaned up well and looks good. Congratulations.
     
  9. Scotlamp

    Scotlamp United Kingdom Subscriber

    Offline
    Joined:
    Sep 15, 2015
    Messages:
    228
    Location:
    Kent UK
    Thank you Martin Proper bit of metal !!
     
  10. phaedrus42

    phaedrus42 Subscriber

    Offline
    Joined:
    Jun 14, 2014
    Messages:
    2,055
    It cleaned up well, Martin. What happened to the hole in the collar where the valve stem goes through?
     
  11. Scotlamp

    Scotlamp United Kingdom Subscriber

    Offline
    Joined:
    Sep 15, 2015
    Messages:
    228
    Location:
    Kent UK
    hole in the collar where the valve stem goes through?
    -Phil

    I had to trim round the v/v opening, it had a thick coat of rusty gunge behind it ,would not budge, it would have come through the metal at some point.
    Well spotted. Its not in a collectable condition anyway.
     
  12. phaedrus42

    phaedrus42 Subscriber

    Offline
    Joined:
    Jun 14, 2014
    Messages:
    2,055
    Not Martin but Michael, sorry! :oops:
     

Share This Page