Search Results

Search Again
Page 2 of 2
  1. terrybull
    Post

    What's missing.

    Thanks Martin And Mathew. I think that I have sorted it. Nothing missing. The small centre piece full of holes was not seated fully home. Once I'd...
    Post by: terrybull, Apr 10, 2015 in forum: Open Forum
  2. terrybull
    Thread

    What's missing.

    I acquired this today in a very dirty state. Cleaned up quite well. I am pretty sure it's an Aladdin. When lit the flame is poor and does not...
    Thread by: terrybull, Apr 10, 2015, 15 replies, in forum: Open Forum
  3. terrybull
    Post

    Bialaddin 300x

    It a fraction bigger than the original cap but stands out being silver and the angle of the photo distorts it a bit. Thanks for all the replies.
    Post by: terrybull, Dec 13, 2014 in forum: Fettling Forum
  4. terrybull
    Post

    Bialaddin 300x

    Here is the lamp now. I cut off the rotten top cap by drilling out the spot welds. Went in pound stretcher and they had some stainless steel...
    Post by: terrybull, Dec 10, 2014 in forum: Fettling Forum
  5. terrybull
    Post

    Good bright bialaddin mantle

    The lamp has been overhauled with all new washers etc. it pumps fine with load of pressure And no leaks. It is burning well. Okay I can't say 100%...
    Post by: terrybull, Dec 5, 2014 in forum: Pressure Lamp Discussion Forum
  6. terrybull
    Thread

    Good bright bialaddin mantle

    I have only 2 lamps at the moment, a Coleman double mantle and Bialaddin 300x. I bought a couple of cheap mantles for the Bialaddin to just get it...
    Thread by: terrybull, Dec 5, 2014, 4 replies, in forum: Pressure Lamp Discussion Forum
  7. terrybull
    Post

    Bialaddin 300x

    I have now got this up and running. I did remove the holed and rusted top piece and made a replacement from a small balti dish. Works a treat and...
    Post by: terrybull, Nov 23, 2014 in forum: Fettling Forum
  8. terrybull
    Post

    Can you "heat and beat" brass?

    It needs to be good and hot, red heat I think and as others have said quench. Have you got any soldered joints anywhere on the tank. You will...
    Post by: terrybull, Nov 19, 2014 in forum: Fettling Forum
  9. terrybull
    Post

    Bialaddin 300x

    So am I correct That the correct way to light it is to prime with meths, and when that is almost out burnt out pump turning the control to prick...
    Post by: terrybull, Nov 18, 2014 in forum: Fettling Forum
  10. terrybull
    Post

    Bialaddin 300x

    That does help David. You're spot on as there is no screw on the end of the knob. I'd noticed on some photos that some have a screw to hold the...
    Post by: terrybull, Nov 18, 2014 in forum: Fettling Forum
  11. terrybull
    Post

    Bialaddin 300x

    Thanks for your replies. The washers arrived today so I re assembled it and pumped. I find it is now leaking slightly from the on off knob spindle...
    Post by: terrybull, Nov 18, 2014 in forum: Fettling Forum
  12. terrybull
    Post

    Bialaddin 300x

    I do have all the parts. I just loosely assemble for the photos while I wait for the washers. Where is the best place to look out for a new top.
    Post by: terrybull, Nov 18, 2014 in forum: Fettling Forum
  13. terrybull
    Post

    Bialaddin 300x

    Photos resized now. I should have taken some 'before' pictures as it was pretty rough but I am pleased with it now apart from the top. [ATTACH]...
    Post by: terrybull, Nov 17, 2014 in forum: Fettling Forum
  14. terrybull
    Thread

    Bialaddin 300x

    I recently acquired this lantern from ebay. Described as working which I dare say it is, we'll sort of as it was leaking badly from the top of the...
    Thread by: terrybull, Nov 17, 2014, 20 replies, in forum: Fettling Forum
Find older messages
Showing results 21 to 34 of 34
Search Again
Page 2 of 2